Koolance PC2-901BW Bedienungsanleitung Seite 1

Protected by U.S. Patents 5,731,954; 6,234,240; 6,313,990Other Technology Pending U.S. & World-Wide PatentsEnglish v2.00Superior Liquid Cooling

5User ManualIPC System DiagramLED Display PanelReservoir &PumpsPower ControlBoardHeat ExchangerFront USB PortsKey Lock

6 IntroductionExos System DiagramPower Control BoardReservoir & PumpsLED Display PanelHeat ExchangerPower ConnectionLiquid Quick-ReleaseValves

7User ManualLED Display PanelMode 1 operates your system at 45% power until the temperature reaches 45ºC(113ºF), then increases to 100% power.Mode 2 o

8 IntroductionReservoir & PumpsThe coolant tank includes many features which are distinctive to a Koolancesystem. It is also translucent for e

9User ManualHeat ExchangerThe heat exchanger, or radiator, is located beneath the fan cooling module. This isthe primary cooling element, specifically

10Power Control BoardNear the heat exchanger, the Power Control Board is responsible for a number oftasks, including: powering the pumps, LED display,

11User ManualChapter2Connecting PC2 &IPC Systems(NOTE: Please skip to the next chapter if you have an Exos System)

12Power Control BoardYou may begin the installation of your Koolance system by mounting a powersupply in the chassis. The liquid cooling system requir

13User ManualThe components in your Koolance system are connected in series. Each systemcontains a heat exchanger and reservoir, but you must choose w

14 Connecting PC2 & IPC SystemsTube to ReservoirCPU Cooler Thermal SensorTube from Heat ExchangerCutting Tube LengthsBefore securely clamping the

iUser ManualThis User Manual is updated regularly. Please be sure to check our support page for anewer version of this guide:

15User ManualEach cooler kit contains clamps to securetubing to the cooler’s nozzles. Thread aclamp onto each tube before connecting it tothe cooler n

16 Connecting PC2 & IPC SystemsClampingAfter every cooler is connected, you may tighten the clamps to secure them.Clamping is done by positioning

17User ManualInevitably, a connection will need to be undone, either because you are addinganother cooler, or because something did not go properly du

18 Connecting Exos SystemsChapter3Connecting ExosTMSystems(NOTE: Please skip to the next chapter if you have a PC2 or IPC System)

19User ManualPositioning the ExosTMAs an external unit, the Exos is de-signed to operate in various locations.Based on testing, Koolance has foundthe

20 Connecting Exos SystemsExternal Quick-Release Nozzles & Power CableThere are two segments of blue external tubing with your Exos system. You wi

21User ManualSlot Interface AdapterThe Slot Interface Adapter allows the Exos to connect with any computer throughan available card slot. It is respon

22 Connecting Exos SystemsThere are 4 main connections to the Slot Interface card which must be made. TheExos may appear to operate without some of th

23User ManualThe black CPU temperature probe is the reading displayed by the front LED panel.You will position this thermal probe later during the ins

24The components in your Koolance system are connected in series. Each systemcontains a heat exchanger and reservoir, but you must choose which cooler

iiWARNING: The Koolance liquid & coolant pack contain chemicalswhich may be harmful or fatal if swallowed. KEEP THIS AND ALLDANGEROUS CHEMICALS O

25User ManualBefore securely clamping the coolers, you must cut appropriate lengths of tubingwith scissors to connect each device. If you are building

26Each cooler kit contains clamps to securetubing to the cooler’s nozzles. Thread aclamp onto each tube before connecting it tothe cooler nozzle.Attac

27User ManualClampingAfter every cooler is connected, you may tighten the clamps to secure them.Clamping is done by positioning the reusable clamp jus

28 Connecting Exos SystemsInevitably, a connection will need to be undone, either because you are addinganother cooler, or because something did not g

29User ManualChapter4Installing Coolers

30Installing CoolersThe chipset cooler is used for both motherboard northbridge and video cardchipsets. If installed, the motherboard must be partiall

31User ManualRemove the protective tape from the bottomof the chipset cooler.Through the original motherboard mounting holes,insert both plastic mount

32Installing CoolersCPU CoolerThe most prominent liquid cooler is also the easiestto install.Apply thermal interface compound directly to theCPU die.

33User ManualThere are 3 center receptacles on the CPU cooler. The tension screw must usethe receptacle that best-aligns it over the processor die’s c

34Installing CoolersCAUTION: Installing the tension screw into the wrong coolerreceptacle can cause insufficient cooler contact, and may result inhard

iiiUser ManualTable of ContentsIntroduction... 1PC2 System Di

35User ManualThe chipset cooler is used for both motherboard northbridge and video cardchipsets. If installed, the video card should be removed from t

36Installing CoolersRemove the protectivetape from the bottomof the chipset cooler.Through the originalmounting holes, insertboth plastic mountingscre

37User ManualOnce mixed, the dual-pack of thermal encapsulatematerial will serve as the heat transfer pad betweenyour drive and the cooling plate. It

38 Installing CoolersUsing the mixing utensil, apply the encapsu-late to the largest heat-producing components:the spindle motor and primary circuit c

39User ManualInstall the Second Hard Drive Kit as youwould a regular Cooler. Thermal encapsu-late is applied to the drive, and the thinmetal “Containm

40 Filling & MaintenanceChapter5Filling & Maintenance

41User ManualCAUTION: Jumping the incorrect ATX power supply pins can causepermanent damage to the power supply.!Your Koolance system is designed to a

42 Filling & MaintenanceCut a small corner in the coolant pack, and slowlyfill the reservoir. You will probably not need theentire amount of liqui

43User ManualCAUTION: Positioning of Exos systems during liquid filling is impor-tant. The Exos must be higher than all internal cooling components,or

44The liquid coolant in your system should be emptied for any of the below reasons:1. To Keep it Clean - Koolance recommends replacing the liquid cool

iv PC2 Series Systems:- motherboard standoffs & insulating washers- motherboard, slot card, 5.25” drive, and floppy screws- hard drive mounting s

45User ManualWe hope your Koolance system will provide you with years of reliable coolingperformance. To help avoid unnecessary RMA issues, we have pr

464. After the system has been on for awhile, the temperature alarm sounds...Make sure that the LED temperature reads at least 50ºC (122ºF) or higherw

47User Manual6. My system appears to be leaking fluid...Since users are allowed to configure their own coolers and clamps, it ispossible a connection

48Limited WarrantyDisclaimerKoolance Incorporated (“Koolance”) warrants each new Koolance liquid-cooledsystem (“the system”), against defects in mater

www.koolance.comISO9001Printed in Korea

1User ManualChapter1Introduction

2 IntroductionCongratulations on your purchase of a Koolance system!As the most sophisticated product of its kind, Koolance offers many uniquefeat

3User ManualThe heart of a liquid cooling system is the pump. This device pushes liquid througheach cooler and into the heat exchanger. Koolance syste

4 IntroductionPower Control BoardPC2 System DiagramHeat ExchangerLED Display PanelReservoir &PumpsLiquid Refill Tap80mm FanHoldersChassis Stab