Koolance VID-487 Bedienungsanleitung PDF herunterladen

NOTE: The video card should be removed from the chassis in order to install this

cooling device.

CAUTION: Removal of the original heat sink my void your manufac-

turer’s hardware warranty. Please consult the manufacturer if unsure,

and keep all original parts in case of a return/RMA.

VID-485,487 Installation Guide v 1.0

Most cards using the VID-series blocks are

disassembled the same way, although heat sink

assemblies of any given model can vary.

The spring-screws on the bottom side should be

removed ﬁ rst. There should be 12-14 of these

on the video card. There may also be smaller

mounting screws on the side of the L-bracket.

Example 1: HD 4870 Disassembly Screws

Example 2: HD 4850 Disassembly Screws

Connecting VID Coolers in SLI or CrossFire

When connecting multiple VID coolers in series, Koolance offers an optional direct-

connect nozzle. This minimizes liquid routing while avoiding potential conﬂ icts with

hardware in between the video cards.

Optional Five Slot Dual Video Connector

(Koolance CNT-VD4)

Optional Two Slot Dual Video Connector

(Koolance CNT-VD2)

Optional Three Slot Dual Video Connector

(Koolance CNT-VD3)

Optional Four Slot Dual Video Connector

(Koolance CNT-VD4)

The heat sink and fan can now be carefully removed. Original thermal paste

may present additional resistance while removing the heat sink. Unplug the heat

sink fan wire. Remove the original RAM thermal transfer material, and wipe any

residual thermal material from the main GPU chipset.

Thermal Paste Area

Thermal pads may have plastic ﬁ lm on one or both sides

that must be removed before application.

Two different sets of heat transfer pads are

included. Each set has a different thickness,

and one should be chosen that offers best contact with

your video card. The thermal pad sheet should be cut into

pieces required for your video block contact areas. A paper

stencil with the proper shapes and sizes is included for

reference.

Place the Koolance block over the video card

and tighten each spring-screw on the reverse

side of the card.

Using the Koolance-supplied screws and plastic insulating washers, tighten each

screw on the reverse side of the card.

Koolance VID coolers include redundant G1/4 threading on both sides. This means

the input/output nozzles can be placed on either side of the cooler.

Two G1/4 “caps” are included

with the VID coolers which can

be placed opposite the desired

nozzle locations.

Place heat transfer pads on each additional area cooled by

the Koolance liquid block. This includes 2 rows of memory,

and 1-2 power/VReg area.

VID-487 Thermal Pad Areas

VID-485 Thermal Pad Areas

Koolance-Supplied Screw and

Insulating Washer

Thermal paste is only required on the main GPU(s). The

other areas will utilize the included heat transfer pads.

Spread thermal compound on the GPU thinly and evenly

using the included paste packet, or a piece of thick paper

(such as a business card). Thermal paste should not be

placed on the surrounding metal support frame or small

surface soldered components.

Inhaltsverzeichnis

Seite 1

NOTE: The video card should be removed from the chassis in order to install this cooling device.CAUTION: Removal of the original heat sink my void you

Verwandte Modelle: VID-485

Kommentare zu diesen Handbüchern

Keine Kommentare

Koolance VID-487 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Koolance VID-487 herunter. Koolance VID-487 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: VID-485

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Koolance VID-487